Our high performance Polyethylene Tanks offer a cost effective storage solution with a higher margin of safety and longer tank life than commodity storage tanks. The seamless one-piece Poly Tank construction is manufactured to the latest revision of ASTM D 1998-97.
| Materials |
Tank Configurations |
Tank Design |
Engineering Assistance |
- HDXLPE
- HDPE
- HDXLPE W/OR1000 (Anti Oxidant Lined System)
|
Vertical Singlewall Tanks
Vertical Doublewall
Vertical I.M.F.O. Full Drain
Vertical Open Top
Cone Bottom Tanks
Horizontal Tanks
Cylindrical Containment Basins
Rectangular Containment Basins |
Rotationally Molded
Seamless One Piece Design
Capacities To 13,650 Gallons
Atmospheric Pressure applications
Suitable For Temperatures to 150 Degrees F.
Wall Thicknesses to 2.2 S.G.
Available to NSF ANSI 61 Standards (If required) |
Approval Drawings
Wall Thickness Calc’s
Factory Test Reports
100 Degree Design Rate |
Filament Wound Fiberglass Tanks are and recommended choice when Fiberglass is the customer specified material or temperatures exceed Polyethylene capabilities.
| Materials |
Tank Configurations |
Tank Design |
Engineering Assistance |
- Ashland - Hetron 922 Vinyl Ester
- Aropol 7142 - Isophthalic Polyester
- Ashland - Ortho
- Ashland—Hetron 970 & 980
- Dow - Derakane 411, 440, 470, 510
- Reichold - Dion 9100, 9200
- Reichold—Atlac 382, 580, 4010A
|
Vertical Singlewall Tanks
Vertical Doublewall
Horizontal Above Ground
Horizontal Underground Singlewall
Horizontal Underground Doublewall
Vertical Open Top
Cone Bottom Tanks
Horizontal Tanks
Containment Basins |
Hand Lay Up (Contact Molding) ASTM 4097
Chop Spray (Contact Molding) ASTM 4097
Filament Winding ASTM 3299
FDA compliant materials when required |
Approval Drawings
Wall Thickness Calc’s
Factory Test Reports
Atmospheric Pressure Applications |
Our Steel Tanks are subject to strict specifications, testing and inspections outlined by the Steel Tank Institute. These Steel Tanks are constructed out of high quality carbon steel and/or stainless steel. Specialty linings & coatings are available to meet your project requirements.
| Materials |
Tank Configurations |
Tank Design |
Engineering Assistance |
- A-36 Carbon Steel
- 304 SS
- 316 SS
|
Vertical Singlewall Tanks (Open Top, Dome Top, Conical Top, & Flat Top)
Vertical Doublewall
Horizontal Above Ground
Vertical Open Top
Cone Bottom Tanks
Horizontal Tanks
Containment Basins
|
API-12F
API-650
UL-142
UL-58
ASME Section VIII |
Approval Drawings
Wall Thickness Calc’s
Factory Test Reports
Atmospheric Pressure Applications |
We offer a wide variety of custom fabricated flexible drop in liners for plating, tank lining, & containment applications. These flexible liners are available in a host of materials from PVC, PE, & Urethanes, custom built to your requirements. Ready for installation upon arrival.
| Materials |
Liner Configurations |
Liner Design |
Engineering Assistance |
- HDPE
- PVC
- PEU/PVC Alloy
- MDPE
|
Open top designs for tanks
Open top for containment
Custom hanging/flange attachments
Flange boots for tank connections
Saddle Liner designs for compartmental tanks |
Flexible drop in style
Thicknesses from 30 mil to 3/16”
Dual layers for air fluid interface
Geo textile membrane pads for enhanced puncture resistance
FDA compliant materials when required
|
Approval Drawings
Data Sheets
RF Welding Construction
|
